Precut Headlight Tint Installation

Precut headlight tints are the perfect way to upgrade, protect and restyle your vehicle's headlights. Precut to fit your year, make, model and sub-model and sold as a pair, they are the ideal way to do-it-yourself and save.

Divider
Recommended Tools

  1. Rapid Prep
  2. Rapid Tac
  3. Rapid Clear
  4. Squeegee
  5. Razor Blade
  6. Heat Gun or Hair Dryer
Divider

Installation Tips

Bullet Ideal application temperature range is between 70º to 80º F (21º to 27º C).
Bullet When possible, turn on your lights to help increase the surface temperature.
Bullet Surfaces must be clean and dry prior to application.
Bullet When removing precut smoked tint pieces from the backing it is best to continuously spray both sides of the film with an application fluid such as Rapid Tac or a 10:1 water to mild soap solution to prevent premature adhesion of the kit to itself.
Bullet Clean your areas thoroughly with a solution such as Rapid Prep.
Bullet Use masking tape to test for adhesion.
Bullet If masking tape curls up and falls off you need to continue cleaning.
Bullet Do not apply during periods of high relative humidity (i.e., when it’s raining).
Bullet Do not bend vinyl film back and forth as this causes the adhesive to wrinkle when applying.
Divider
Clean Headlights

Step 1: Preparation and Cleaning

We hate to say it but your headlight tint job will only be as good as your cleaning and preparation. That's why it is of the utmost importance to remove all dust, oil and residues not only from the windows but from the surrounding panels and even the area in which you'll be tinting.

Begin by cleaning the your headlight housing, the lens and the surrounding areas. For proper adhesion, clean all surfaces using a 2:1 mixture of water to isopropyl alcohol or Rapid Prep.

Note: Prior to cleaning test solution in an inconspicuous area. Use a clean, lint-free cloth to cleanse the application area. Insure the lens is dry and all oils and residues have been removed prior to application. A good test is to see if masking tape will stick to the application surface, if it sticks then the surface is ready for application. If it does not stick then further cleaning may be necessary.

Divider
Spray and Lubricate Headlights

Step 2: Spray and Lubricate Lenses

Spray a liberal amount of the Rapid Tac onto the light which will allow you to reposition the film during the application process. Be sure to include gaskets and trim around the lights as well.
Divider
Peel Liner Away

Step 3: Remove Liner

As always, mist your fingers, and spray the Rapid Tac on the tint as well.

In order to remove the tint from the liner, carefully and slowly lift a corner and begin to peel the liner. Spray both sides of the tint with application fluid. This will allow you to reposition the film on the light as well as preventing the tint from sticking to itself.
Divider
Alight and Apply Tint to Headlights

Step 4: Alight and Apply Tint

Having sprayed the light with application fluid, apply the wet, adhesive side of the film to the lens.

Reposition the film to align it to the edges. You may use the application tabs if they are available on your kit.

Not all kits are designed with these tabs.

Note: The film may appear to be "short" or "too large" at this stage of the installation. This is because the film has not been heated and stretched yet or trimmed.
Divider
Spray and Lubricate Tint

Step 5: Spray Tint

Spray the outside of the film with Rapid Tac of the soap and water solution again. This will reduce scratching. Spray the area once again to allow repositioning.
Divider
Squeegee Headlight Tints

Step 6: Transfer the Tint from Outside of Glass to Inside

For flatter areas, apply pressure to one end of the film so that it begins to adhere to one end of the area. Using a squeegee, press down and squeegee the film with smooth sweeping motions. If this is being done properly, you will see the water exit from underneath the film. Do this across the remainder of the area.

If large bubbles are present, peel up the film to that area and apply again. Rtint vinyl film is very forgiving when both the area and the adhesive side of the film is wet. Keeping the film wet allows you to pull and reapply numerous times if not satisfied with results prior to heating the film.
Divider
For headlight tint kits with slits spray the outside of the film with solution again. This will reduce scratching. Spray the light once again. Proceed as above being sure to liberally apply the solution to both sides of the film. When the film is stretched into position one of the sections or flaps of the film will naturally fall over the other. Lightly smooth the flap down until flat. Using a razor gently score away the overlapping film until you can easily pull the excess film away.
Divider

For lights with large curves (the most common lights on the market today), spray the outside of the film with solution again. This will reduce scratching. Spray the light once again. Apply pressure to the center of the film on the light with a squeegee so that it begins to adhere to one end of the light. It may be easier to have a partner help you by holding the film as you begin the next step. Gently begin to heat the film on one end from the center with a hair dryer or heat gun on a low setting. Take your time in heating the film, you do not want to melt the film.

Apply the remainder of the film by moving in a spiral or circular motion working outwards towards the edge of the light. Keep the film "warm" by continually heating it will allow it to stretch up to 2% to 5% and conform. This is the only way you can apply tint to a curved light unless the kit has slits which are intended to be overlapped and cut-away.
Divider
Heat Your Headlight Tints

Step 7: Heat the Tint

Using a heat gun heat the tint to aid in shrinking and curing the film.
Divider
Clean Headlights

Step 8: Trim Away Excess

Remove excess vinyl which may hang over the edges.
Divider
Pop Remianing Bubbles

Step 9: Allow to Cure & Pop Any Bubbles

Allow film dry for a minimum of 30 minutes and carefully wipe off any excess solution. If all moisture has not been properly removed from under the film some fogginess may occur. This is completely normal. Film is breathable and porous – cloudiness/fog will evaporate with a few days to a few weeks. Depending on film thickness and sunlight/heat exposure. Any surface texture, scratches, or ripples will also disappear during this curing process.

Note: Adhesion may be difficult in cold weather, humid areas or if the surface has not been properly cleaned prior to application.

After 24 hours, if there are any small bubbles you may proceed to pop them with a sharp needle. Pop them and then use a squeegee to press out air or fluid. DO NOT spray any more application fluid at this point.
Divider

Smoked HeadlightsStep10: Tint Complete

Once you've popped any remaining bubbles, you're done. Use Rapid Clear to polish your headlight tints and be sure not to take your ride through an automated wash nor use power washers.
Divider