CATEGORIES

i3

i8

M

M2

M3

M4

M5

M6

M8

X1

X2

X3

X4

X5

X6

X7

Z3

Z4

Z8


BMW Vehicle Wraps

BMW vehicle wraps are the perfect way to restyle or change your Bimmer's color without the cost or commitment of an repainting it. And, since most aftermarket paint jobs don't deliver the same quality results as factory paint, they tend to chip and peel quite easily. So, whether you're wanting to restore your BMW 1 Series' exterior with a color change Series 1080 vinyl wrap or you want to wrap your Z4's hood with an Rwraps™ 3D Carbon Fiber wrap we've got the right product for the job here. Put your trust in our premium BMW vehicle wraps that will last longer and look better than any aftermarket spray job out there!

 Wrap Every Surface

Whether you've been thinking of a complete color change or just want to wrap your hood, trunk, fenders or mirrors, we've got the right vinyl wrap in the right size for you. Both our Rwraps™ and 3M™ vehicle wraps are meant to be applied over you factory paint finish and are removable so you can take them off without damaging the underlying surface.

So what are your options for wrapping your BMW? You might be excited to know that you don't have to commit to wrapping your whole 3 Series from bumper to bumper. Instead, you can focus on individual panels to protect against specific dangers or to achieve a particular look. By applying your vehicle wrap one panel at a time you have complete control over how much of your car is covered.

Here's a look at some different options you have when it comes to applying a vehicle wrap to your car:

  • Hood — 72-96 inches
  • Roof — 72-96 inches
  • Trunk — 60-72 inches
  • Spoilers — 60 - 72 inches
  • Mirrors — 12-24 inches
  • Chrome Trim Deletes — 12-36 inches

 
Please note: BMW vehicle wraps are meant for application only on OEM paint jobs. They are not meant to be applied on aftermarket paint jobs as they are not cured to the same extent nor are they clear coated in the way factory paints are. In addition, when choosing your car wrap, carefully measure the area or component to be wrapped and select the appropriate amount of material needed, remembering to factor in an overhang that will be trimmed after application.

BMW Vehicle Wraps Specs

All of our BMW vehicle wraps are made for use it right out of the box so no need to laminate or mount them. And, because they're engineered with dual color layers for dimensional stability and durability, you can depend on them not to discolor or deform even around the most extreme of curves. Enjoy the convenience and quality of our pro-grade, DIY ready films and get to wrapping.

  • Dual-cast, dual-layered vinyl films are color fast and won't deform
  • Yours in over 200 colors and finishes
  • Pressure-activates, heat-sensitive adhesives
  • Air-release channels for bubble-free results
  • Buy by the foot in12, 24 60 inch rolls (Series 1080 is only available in 60-inch wide format)
  • Semi-permanent and removable


Restyle and Restore Your BMW

Whether you want to wrap your BMW X5's roof and tailgate with Series 1080 Satin film, your all new X3 in a Matte Metallic film or want to add shade-shifting Satin Flip vinyl to your BMW M3, we've got just the thing you're looking for. And, since there's no better advertising than a satisfied customer, we're excited to offer our $20 Cash Back Photo Rebate program to you. Just wrap your BMW with any of our vinyl films, take 5 or 6 photos and write up a quick review of your experience. We'll issue you up to a $20 Cash Back refund and then post your review and pics to our site and blog. What could be better? So, hurry up and pick up a wrap kit for your BMW today!



Clean It Right for Best Results


Preparing Your BMW for Vinyl Wraps

Without proper preparation and cleaning of your installation area and vehicle, you can't expect to get good results. Making sure your garage or application area is dust free is absolutely essential otherwise it will be attracted to the underside of film. Check out this post and learn how to clean like a pro so you don't end up throwing away hard earned cash..

READ MORE

Post-Heat or Your Wrap is Toast


Why You Need to Post Heat

Post-heating is one of the most important yet most often neglected steps by DIY installers. Whenever you're wrapping anything with a curve, corners or creases, you need to use this technique if you want the film to perform and give you professional-looking results that will last.

READ MORE

Heat Gun Tips for the DIY Installer


Heating Your Wrap for Ultimate Performance

Most DIY wrap installers try to do without this tool but if there's one thing you need to wrap it's a heat gun. Still, it's never a simple as buying a heat gun and turning it on. Take a few minutes to read this article and learn how to make the most out of your BMW vehicle wrap.

READ MORE

Make Your Install Painless with Pre-Stretching


Cold Pre-stretching is a Game Changer

Want to know the one secret that separates the pros from the amateurs? It's the German-developed technique of cold pre-stretching vehicle wraps. Most amateurs overstretch the film which results in shrinkage and under performance. Separate yourself from the pack and get the know-how to wrap your BMW today!

READ MORE

Get More with 1080 Series Vinyl Wraps


1080 Series Vinyl Wraps

When you want to wrap your car, truck, boat, SUV or just about anything else, you want 3M™ 1080 Series films. Made by a company with an unparalleled reputation, you'll love the look and performance of these DIY car wrapping films. 3M™ 1080 Series offer you a choice of more than 80 different colors and finishes so you can get exactly the look you want without the mess of painting it yourself or the expensive of bringing your car into a shop.

READ MORE
rvinyl guy

BMW Accessories


Reviews | 4 Reviews

Avg Rating
4.63
Out of 5

1st time was a disaster
by TamWam, Plant City, Florida 4.50

3/16/2021
review-star review-star review-star review-star review-star
Tried to wrap my hood and lets just say it didn't turn out the way i wanted. Seemed difficult to get the bubbles out. Seemed difficult to work with and tore when i pulled to hard. Wasted money and my time. They say second time is a charm so I'll try one more time

1st time was a disaster
by TamWam, Plant City, Florida 4.50

3/16/2021
review-star review-star review-star review-star review-star
Tried to wrap my hood and lets just say it didn't turn out the way i wanted. Seemed difficult to get the bubbles out. Seemed difficult to work with and tore when i pulled to hard. Wasted money and my time. They say second time is a charm so I'll try one more time

I was missing an inch in the back so I had to improvise
by Florent Paz, Santa Cruz 4.50

5/14/2021
review-star review-star review-star review-star review-star
I had to improvise by cutting a piece and sticking it in the back other than that great material

Reviews

4.63 | 4 Reviews